Un segundo intercalar, segundo adicional o segundo bisiesto es un ajuste de un segundo para mantener los estándares de emisión de tiempo cercanos al tiempo solar medio. Los segundos intercalares son necesarios para mantener los estándares sincronizados con los calendarios civiles, cuya base es astronómica. La Unión Internacional de Telecomunicaciones ha propuesto añadirle una hora al reloj cada 600 años y abolir este tiempo intercalar. China y Gran Bretaña se oponen al cambio, pero Estados Unidos, Italia, Francia, Alemania, Japón y Rusia lo apoyan y, entre las alternativas, figura retroceder al reloj una hora cuando la variación haya acumulado un retraso de media hora. Según los cálculos de la Universidad de Bonn, eso ocurriría en 2600. Los estándares para el tiempo civil están basados en el Tiempo Universal Coordinado (UTC), que se mantiene usando relojes atómicos extremadamente precisos. Para mantener el UTC cercano al tiempo solar medio, ocasionalmente se corrige mediante un ajuste de un segundo que se añade, lo que supone encontrarse con un minuto con 61 segundos. Durante largos períodos, se deben añadir estos segundos intercalares a un ritmo creciente que corresponde con una parábola cercana a 31 s/siglo² (ver ΔT). También está prevista la eliminación de un segundo, teniendo un minuto de sólo 59 segundos, pero no ha sido necesario en el pasado y basándose en las predicciones para la rotación de la Tierra tampoco lo será en el futuro.

Leer el artículo completo en Wikipedia · CC-BY-SA

A leap second is a one-second adjustment that is occasionally applied to Coordinated Universal Time (UTC) in order to keep its time of day close to the mean solar time, or UT1. Without such a correction, time reckoned by Earth's rotation drifts away from atomic time because of irregularities in the Earth's rate of rotation. Since this system of correction was implemented in 1972, 26 leap seconds have been inserted, the most recent on June 30, 2015 at 23:59:60 UTC, and the next leap second will be inserted on December 31, 2016, at 23:59:60 UTC. The UTC time standard, which is widely used for international timekeeping and as the reference for civil time in most countries, uses the international system (SI) definition of the second, based on atomic clocks. Like most time standards, UTC defines a grouping of seconds into minutes, hours, days, months, and years. However, the duration of one mean solar day is now slightly longer than 24 hours (86400 SI seconds) because the rotation of the Earth has slowed down. Therefore, if the UTC day were defined as precisely 86400 SI seconds, the UTC time-of-day would slowly drift apart from that of solar-based standards, such as Greenwich Mean Time (GMT) and its successor UT1. The purpose of a leap second is to compensate for this drift, by occasionally scheduling some UTC days with 86401 or (in principle) 86399 SI seconds. Specifically, a positive leap second is inserted between second 23:59:59 of a chosen UTC calendar date (the last day of a month, usually June 30 or December 31) and second 00:00:00 of the following date. This extra second is displayed on UTC clocks as 23:59:60. On clocks that display local time tied to UTC, the leap second may be inserted at the end of some other hour (or half-hour or quarter-hour), depending on the local time zone. A negative leap second would suppress second 23:59:59 of the last day of a chosen month, so that second 23:59:58 of that date would be followed immediately by second 00:00:00 of the following date. Because the Earth's rotation speed varies in response to climatic and geological events, UTC leap seconds are irregularly spaced and unpredictable. Insertion of each UTC leap second is usually decided about six months in advance by the International Earth Rotation and Reference Systems Service (IERS), when needed to ensure that the difference between the UTC and UT1 readings will never exceed 0.9 seconds. 26 positive leap seconds have been inserted so far, with a twenty-seventh scheduled for December 2016.

Leer el artículo completo en Wikipedia · CC-BY-SA